Splint or Slabs

Absolute washable orthopedic Immobilizer for immobilization in the pre-operative, post-operative and rehabilitation period.

INTENDED USE

  • Acute swelling of fractured / injured limb / joint
  • Pre-operative stabilization
  • Post-operative support after surgery
  • Ligament sprain / soft tissue injury
  • Support during rehabilitation

FlexiOH Splint or Slab

FlexiOH Splints / Slabs are designed for immobilization in the pre-operative, post-operative, acute swelling and rehabilitation period. FlexiOH has an built-in soft hook and loop fastener that secures the splint over the limb which is very comfortable for skin contact. With unique FlexiOH technology, this splint gives better patient comfort along with breathability and washability. For application of FlexiOH Splint / Slab, healthcare professional need to apply it on the patient’s limb with the soft hook and loop fastener and then cure it with the RizyCure curing light device (recommended) for 3-10 minutes depending on the size of splint/ slab. Once it is rigid, it will provide support during rehabilitation. With velcro, the splint can be removed / adjusted anytime for dressing and rehabilitation.

FlexiOH® Splints / Slabs are available in 9 different sizes : 3 in X 9 in, 3 in X 12 in, 3 in X 15 in, 4 in X 12 in, 4 in X 15 in, 4 in X 18 in, 5 in X 12 in, 5 in X 15 in and 5 in X 18 in. All of the Splints / Slabs vary in terms of length and width.

AVAILABLE SIZES

Width Vs. Length 10 inch (L) 12 inch (L) 15 inch (L) 18 inch (L)
3 inches (W) 3 in X 9 in 3 in X 12 in 3 in X 15 in
4 inches (W) 4 in X 12 in 4 in X 15 in 4 in X 18 in
5 inches (W) 5 in X 12 in 5 in X 15 in 5 in X 18 in

APPLICATION PROCESS
FlexiOH Splint or Slab Immobilizer application process is as follows:

FlexiOH Splint or slab application process

Step – 1 : Choose the appropriate size from given chart

FlexiOH Splint or slab application process

Step – 2 : Take the suitable size for the application

FlexiOH Splint or slab application process

Step – 3 : Apply the splint by passing the hand in between the loop and splint

FlexiOH Splint or slab application process

Step – 4 : Check the position of the loops is comfortable to the patient

FlexiOH Splint or slab application process

Step – 5 : Start tightening the first loop at the palm circumference

FlexiOH Splint or slab application process

Step – 6 : Tighten the last loop at the end

FlexiOH Splint or slab application process

Step – 7 : Tighten all in between loops to fit the splint perfectly before curing

FlexiOH Splint or slab application process

Step – 8 : Take a RizyCure curing light device

FlexiOH Splint or slab application process

Step – 9 : Start exposing the splint / slab with RizyCure curing light device

FlexiOH Splint or slab application process

Step – 10 : Re-tighten all the loops once the splint /slab is rigid

FlexiOH Splint or slab application process

Step – 11 : Cut the extra length of loops with scissors

FlexiOH Splint or Slab Immobilizer provide ~30 % open area of skin to breathe, wash, and exposure to sunlight which all are necessary to maintain healthy skin.